Green lab protocol for vacuum infiltration transformation of Arabidopsis

互联网2013-09-06

774

This protocol is adapted from protocols by Nicole Bechtold (Bechtold et al. 1993),
Andrew Bent (Bent et al. 1994) and Takashi Araki. No claims are made that any of the steps
are necessary or ideal; these experiments have not been done. However, this protocol gives us
very good results, with at least 95% of all infiltrated plants giving rise to transformants,
and a transformant rate of 1-4% of seed.

1.   Sow seeds of ecotype Columbia in lightweight plastic pots prepared in the
     following way: mound Arabidopsis soil mixture into pots (We use 3 1/2 inch
     to 4 inch square pots), saturate soil with Arabidopsis fertilizer , add more soil
     so that it is rounded about 0.5 to 1 inch above the top, dust with fine
     vermiculite, cover soil with a square of window screen mesh (Circle Glass
     Co., Detroit, MI) and secure mesh with a rubber band.

2.   Grow plants under conditions of 16 hours light/ 8 hours dark at 20 °C to
     22 °C, fertilizing from below with Arabidopsis fertilizer once a week , adding
     approximately 0.5" to each flat. Thin the plants to one per square inch or
     fewer per pot. After 4-6 weeks, depending on your conditions, plants will be
     ready to infiltrate when they are at this stage: the primary inflorescence is
     5-15 cm tall and the secondary inflorescences are appearing at the rosette.
     No clipping of bolts is necessary before infiltration.

3.   In the meantime, transform your construct into Agrobacterium tumefaciens
     strain GV3101 (C58C1 Rifr) pMP90 (Gmr) (Koncz and Schell 1986 ). When plants
     are ready to transform, inoculate a 500 ml culture of YEP medium containing
     50 mg/l rifampicin, 25 mg/l gentamycin and the appropriate antibiotic for your
     construct with a 1 ml overnight starter culture. Be sure to water your plants
     well the day before infiltration so that the stomata will be open that day.

4. Grow culture overnight at 28 °C with shaking, until culture OD600 is> 2.0.
Spin down the culture and resuspend it in 1 liter of infiltration medium.

          Infiltration medium (l liter)
          2.2 g MS salts
          1X B5 vitamins
          50 g sucrose
          0.5 g MES
          pH to 5.7 with KOH
          0.044 µM benzylaminopurine (be sure the final concentration is micro molar).
          200 µl Silwet L-77 ( OSi Specialties request that purchases be
                         made at Lehle Seeds, fax # (512) 388-3974
                         catalog # vis-01)

5.   Place resuspended culture in a Rubbermaid container inside a vacuum
     desiccator. Invert pots containing plants to be infiltrated into the solution so
     that the entire plant is covered, including rosette, but not too much of the soil
     is submerged. One good way to do this is to place the corners of the pots
     on rubber stoppers sitting in the culture. Make sure no large bubbles are
     trapped under the plant.

6.   Draw a vacuum of 400 mm Hg (about 17 inches). Once this level has
     been obtained, close the suction (i.e., so that the vacuum chamber is still
     under 17 inches of mercury but the vacuum is not still being directly
     pulled) and let the plants stay under vacuum for five minutes. Quickly
     release the vacuum. Briefly drain the pots, place them on their sides in a
     tray, cover the tray with plastic wrap to maintain humidity, and place the
     flats back in a growth chamber. The next day, uncover the pots and set
     them upright. Keep plants infiltrated with different constructs in separate
     trays from this stage on.

7.   Allow plants to grow under the same conditions as before (see step 2).
     Stake plants individually as the bolts grow. The leaves that were infiltrated
     will degenerate, but plants continue growing until they finish flowering.
     Gradually reduce water and then stop watering to let them dry out.
     Harvest seeds from each plant individually.

8.   Prepare large selection plates:      4.3 g/l MS salts
                                                       1X B5 vitamins (optional)
                                                         1% sucrose
                                                         0.5 g/l MES
                                                         pH to 5.7 with KOH
                                                         0.8% phytagar
                                                         Autoclave.
                                                         Add antibiotics (30 g/ml works well for kanamycin).
                                                         Pour into 150 X 15 mm plates.
     We also add vancomycin at 500mg/l to control bacterial growth.

9. Dry plates well in the sterile hood before plating. Twenty minutes to half an
hour with the lids open is usually sufficient.

10. For each plant sterilize up to 100 µl of seeds (approximately 2500 seeds) and
     plate out individually. Sterilize seeds (7 minutes rocking in 50%
     bleach/0.02% Triton X-100, 3 rinses in sterile distilled water). Resuspend
     seeds in approximately 8 ml sterile 0.1% agarose and pour onto large
     selection plates as if plating phage. Tilt plate so seeds are evenly distributed,
     and let sit 10-15 minutes. After a while the liquid should soak into the
     medium; if evaporation is too slow, open the plate in the hood and let dry until
     the excess liquid is gone. Seal plates with Parafilm or paper surgical tape
     and place in a growth room.

11. After 5 to 7 days, transformants will be visible as green plants. Transfer
     these onto "hard selection" plates (100 x 20 mm plates with same recipe as
     selection plates but with 1.5% phytagar) this allows roots to elongate and
     eliminates any false positives. Place in growth room.

12. After 6-10 days, plants will have at least one set of true leaves. Transfer
     normal conditions. Keep covered for several days. Note: We usually move
     just one transformant to soil from any one plant that was infiltrated, to ensure
     independent transformants.

Green lab protocol for vacuum infiltration transformation of Arabidopsis

References:

Solutions

Commonly asked questions about this vacuum infiltration method: